Begagnad blaser f16
These are guns that are quite fascinating with their craftsmanship, but laser-focused on central European hunting conditions and traditions. That all started to change with the first Blaser I wrote about more than 30 years ago, the R It was a straight-pull rifle whose largely aluminum receiver would accept multiple bolt heads and barrels, allowing the user to configure the gun for multiple calibers.
This led eventually to the R93, which is another straight-pull with an unusual collet bolt head. The F16 comes in three configurations: Game; Intuition specifically dimensioned for women ; and Sporting. The latter model is the subject of this review. The first thing I noticed about the F16 Sporting is the combination of very well-figured and high-gloss finished Grade 4 walnut with matte-finished metalwork.
The frame has a very dark pewter color, broken only by the F16 rollmark in red, while the barrels are matte charcoal. The begagnad blaser f16 design for an over-under is a shallow frame, and it is achieved here at 2. It has a distinctly Teutonic look in the proportion between barrel and frame at the breech. Now, millions of birds and targets have fallen to the good old Browning Begagnad blaser f16 and other over-unders like the Winchesterwhich also have a deep frame by current standards.
Blaser accomplishes this by using a bifurcated bolt at the very bottom of the standing breech. This arrangement allows the barrel to sit at the very bottom of the frame. The ejectors are tripped by what looks like two extra firing pins in the standing breech. These impact plungers in the ejectors are not under spring pressure when the gun is at rest.
Blaser F16 Game Sörétes Fegyver
After firing, the ejector springs are compressed as the barrels are lowered, giving the begagnad blaser f16 lots of leverage. Blaser claims this reduces shooter fatigue. The face of the standing breech is a separate component retained by a pair of Torx screws that incorporates the firing pins, ejector trips and the top lever plunger. As is appropriate for a competition gun, the safety is manual.
It both presses forward on the selector block, disengaging that part from the sears, and lowers an interceptor from the underside of the tang just below the thumbpiece of the top lever. The latter part is intended to prevent the hammers falling on the firing pins if the shotgun is dropped. The safety is never used in competition with many competitors locking it out. Scratching that nice wood, on the other hand, definitely should worry you.
Pushing the selector to the left chooses the under barrel. The trigger is mechanical but has an impressive inertia block to help prevent doubling. Both barrels touched off with a 3-pound pull. There was a time when very disparate trigger pulls were common, but manufacturers have learned that tends to put off consumers, so you rarely see an over-under these days with varying pulls.
Push the supplied 5mm hex key through the central slot in the recoil pad and turn out the balancer, which threads onto the short through-bolt at the rear of the frame. These bite directly into the stock wood, so be judicious about doing this. I would have thought threaded inserts in the buttstock with machine screws to retain the recoil pad would have been the choice here.
With the recoil pad removed, you can shake out the balancer, as well as a spacer and spring package. The latter consists of two opposed pairs of Belleville washers that prevent the balancer begagnad blaser f16 the buttstock at the wrist.
Puska teszt: Blaser F16 Game sörétes puska
The balancer is a threaded rod with a socket at the front that rests against the spring package and a rubber buffer at the rear, which locates it inside the buttstock recess. In between are three, 2-ounce, steel cylinders that clamp to a flat surface on the threaded rod with hex socket screws. They are fitted with rubber O-rings for a snug fit inside the stock.
You can leave all three in place, remove one or two or all of them. You can position them anywhere on the rod you wish, allowing almost infinite adjustment. In my opinion, any of those three positions is just fine.
Információk
This looked perfectly nice at the gun club, but really came into its own when under the bright lights of the photo studio. You can specify wood up to Grade At that point, the wood would probably cost more than the gun itself. Suffice it to say, the Grade 4 wood is plenty impressive. You can choose the drop at heel of either 2 or 2¼ inches.